The SFP GBIC-106 module is designed to convert an electrical signal into an optical signal. It is designed for single mode fiber transmission (SM) using one optical fiber terminated with an LC optical connector. Fiber type: single mode (SM) – 8.3/125?m, 8.7/125?m, 9/125?m, 10/125?m. Transmission speed: 1,25Gb/s. Transmission range: up to 20km. Optical Connector Type: 1xLC. Wavelength Tx/Rx: 1550nm / 1310nm. Standards and protocols: IEEE 802.3z 1000Base-FX. Power supply: 3,3VDC (power from SFP port). Built-in DDM (Digital Diagnostics Monitoring). The module has a snap-lock system for optical connectors. Proper communication with other devices requires the use of the GBIC-105 module.

Splitter P-POE2 enables transfer of power and data to two IP PoE cameras or other devices, that are compliant with this standard, using UTP twisted pair cable cat5e. Connector for twisted pair cable: RJ45 socket (TCP IP and power supply). Connectors – PoE switch: 2 x RJ45 plug. Connectors – IP cameras – PoE: 2 x RJ45 plug. TCP IP data transmission: 1-2 and 3-6 pairs. Power transmission: 1-2 and 3-6 pairs. Dimensions: W=120 H=19 D=19 mm. Designed for 10Mbit/s and 100Mbit/s network.

Power supply: 44÷57VDC. Power supply output: 12VDC / 1,25Amp. Input connector: RJ45 socket. Output connector: Power supply 12VDC - JACK 5,5/2,1 plug. Data – RJ45 plug. Input power supply pairs: 1/2(+) 3/6(-) or / and 4/5(+) 7/8(-). Efficiency: 84%. Protections: OLP, SCP. Dimensions: L=86 W=30 H=25 mm. Designed for 10Mbit/s and 100Mbit/s network. Operation with PoE switches (standard PoE – IEEE802.3af/at). Operation with passive PoE switches (supplied pairs: 4/5 and 7/8).

SCB batteries are maintenance-free Valve Regulated Lead Acid Batteries with self-regulating one-sided safety valves and internal gas recombination. The batteries are made in AGM (Absorbent Glass Mat) technology; the electrolyte is held in the glass mat. The technology used allows installing batteries in places with natural (gravity) ventilation and minimizes maintenance. They are dedicated for devices requiring emergency power to a load when the input power source or mains power fails, such as: buffer power supplies used, among others, in CCTV systems, alarm systems (Intrusion Detection Systems, IDS), and access control systems (ACS), UPS units, etc... Nominal voltage: 12 VDC. Nominal capacity: 18 Ah. Projected lifespan: 2 to 3 years at 20ºC. Charging current: Recommended 1.8 Amp, Maximum 5.4 Amp. Dimensions: W = 181 , H = 167 , D = 77 [mm, +/-2].

SCB batteries are maintenance-free Valve Regulated Lead Acid Batteries with self-regulating one-sided safety valves and internal gas recombination. The batteries are made in AGM (Absorbent Glass Mat) technology; the electrolyte is held in the glass mat. The technology used allows installing batteries in places with natural (gravity) ventilation and minimizes maintenance. They are dedicated for devices requiring emergency power to a load when the input power source or mains power fails, such as: buffer power supplies used, among others, in CCTV systems, alarm systems (Intrusion Detection Systems, IDS), and access control systems (ACS), UPS units, etc... Nominal voltage: 12 VDC. Nominal capacity: 7 Ah. Projected lifespan: 2 to 3 years at 20°C. Charging current: Recommended 0.7 Amp, Maximum 2.1 Amp. Dimensions: W = 152 , H = 100 , D = 65 [mm, +/-2].

A safety backed power supply module is designed for an uninterrupted supply of alarm system devices that require a stabilized voltage of 12 VDC (+/- 15%). A linear stabilization system, which has been used in the unit, provides voltage with a lower noise level and a faster response to interference compared to a switched mode regulator. The PSU module provides a voltage of U = 13.8 VDC with current capacity: (1) Output current 1Amp (without battery). (2) Output current 0.9Amp + 0.1Amp for battery charge. In the event of a power failure, a backup battery is activated immediately. Power supply: 16V ÷ 17 VAC. Current consumption 1.9Amp. Output voltage 12.8V ÷ 13.8 VDC - backup operation. 14W PSU power. Output voltage adjustment range 12 ÷ 14.5 VDC. Output current: (1) 1Amp without battery. (2) 0.9Amp + 0.1Amp to charge the battery. Linear voltage regulator. Protection types: short circuit, overload, overheating, overvoltage. Dimensions: 90 x 72 x 55 mm. Working temperature: -10° C ... + 40° C. Transformers required: AWT150, AWT070.

A buffer PSU module is intended for an uninterrupted supply to devices requiring stabilised voltage of 12VDC (+/-15%). The PSU module provides voltage of 13.8 VDC with current capacity. In case of power failure, a battery back-up is activated immediately. Power supply: 18V÷22VAC/50Hz/with transformers AWT5161820, AWT037, AWT500. Power supply output: 2Amp/13.8VDC. Battery charging current: 0.2Amp/0.5Amp. Efficiency: 86%. Protections: short-circuit, overload, overheat, over voltage. Technical outputs OC type: EPS – AC network failure, PSU – power supply failure, LoB – low battery voltage. Dimensions: L=86, W=63, H=40 [+/- 2mm].

A buffer PSU module is intended for an uninterrupted supply to devices requiring stabilised voltage of 12VDC (+/-15%). The PSU module provides voltage of 13.8 VDC with current capacity. In case of power failure, a battery back-up is activated immediately. Power supply: 18V÷22VAC/50Hz/with transformers AWT8161820, AWT039, AWT800. Power supply output: 3Amp/13.8VDC. Battery charging current: 0.5Amp/1Amp. Efficiency: 81%. Protections: short-circuit, overload, overheat, over voltage. Technical outputs OC type: EPS – AC network failure, PSU – power supply failure, LoB – low battery voltage. Dimensions: L=88, W=93, H=55 [+/- 2mm].

Switch mode buffer power supply unit for HD cameras 13,8VDC and recorder 12VDC, and recorder space + transmitters. Size: 425 x 540 x 190+14 mm. ?I=11A, 16x0.8A/13.8VDC + 1x5A/12VDC (RJ45 + JACK5.5/2.1). Set includes P-TRPV120 transmitters for up to 12 cameras (Recorder space: 380 x 335 x 80 mm). Tamper: 1xNC, 17Ah-UVP (battery protection).

Switch mode buffer power supply units for HD cameras 13.8VDC and recorder 12VDC, and recorder space. Size: 425 x 535 x 190+14 mm. ?I=11A (8x0.75A/13.8VDC + 1x4A/12VDC). Recorder space: 380 x 335 x 80 mm. Tamper:1xNC, 17Ah-UVP (battery protection).

Switch mode buffer power supply unit (transformerless) for cameras 12VDC (+/- 15%). Size: 285 x 297 x 80+8 mm. Uin=176÷264VAC, Uout=13,8VDC/5x1A. ?I=5A+2A. Tamper: 1xNC, 17Ah. SCP (short-circuit protection) with standard fuses, OVP (over voltage protection), OLP (overload protection), UVP (deep discharge battery protection).

Switch mode buffer power supply unit (transformerless) for cameras 12VDC (+/- 15%). Size: 285 x 297 x 80+8 mm. Uin=176÷264VAC, Uout=13,8VDC/9x1A, ?I=9A+1A. Tamper: 1xNC, 17Ah. SCP (short-circuit protection) with standard fuses, OVP (over voltage protection), OLP (overload protection), UVP (deep discharge battery protection).

Switch mode buffer power supply units for HD cameras 13.8VDC and recorder 12VDC, and recorder space. Size: 425 x 535 x 190+14 mm. ?I=11A (8x0.75A/13.8VDC + 1x4A/12VDC). Recorder space: 380 x 335 x 80 mm. Tamper:1xNC, 17Ah-UVP (battery protection).

Power supply for cameras 12VDC with independent control of each output channel. Size: 205 x 220 x 50+8 mm. Uin=85÷264VAC, Uout=12,0÷15VDC. 4 x adjustment. 4x1A (independent regulation and galvanic separation of each channel). OVP (over voltage protection), SCP (short-circuit protection) with standard fuses.

Power supply for cameras 12VDC with independent control of each output channel. Size: 365 x 220 x 70+8 mm. Uin=85÷264VAC, Uout=12,0÷15VDC. 8 x adjustment. 8x1A (independent regulation and galvanic separation of each channel). OVP (over voltage protection), SCP (short-circuit protection) with standard fuses.

Power supply for 12VDC cameras, for long lines with galvanic separation of each channel dedicated to DCDC-H inverters. Size: 270 x 154 x 80+8 mm. Uout=30V÷35VDC (100% load ÷ 0% load). 4x1A@30V DC max. SCP (short-circuit protection): 4x T 1A with standard fuses. Power supply - intended to the DCDC10H and DCDC15H converters).

Mount bracket for mounting TOR, TRP and TRZ transformers on a DIN rail (35mm).

Power: 20VA. Power supply: 230V/50Hz/0.12A. Power supply output: 12V/1.6Amp lub 14V/1.4Amp. Enclosure: PC/ABS V-O, IP30. Thermal fuse 130º C. Notes: epoxy encapsulated. For mounting on a DIN rail, required bracket: AWO466. Dimensions: 72 x 124 x 70 mm. Operating temperature: -10 ... +40° C.

Power: 20VA. Power supply: 230V/50Hz/0.12A. Power supply output: 16V/1.2Amp lub 18V/1Amp. Enclosure: PC/ABS V-O, IP30. Thermal fuse 130ºC. Notes: epoxy encapsulated. For mounting on a DIN rail, required bracket: AWO466. Dimensions: 72 x 124 x 70 mm. Operating temperature: -10 ... +40° C.

Power: 50VA. Power supply: 230V/50Hz/0.25Amp. Power supply output: 16V/3Amp lub 18V/2.8Amp lub 20V/2.5Amp. Enclosure: PC/ABS, V-O, IP30. Thermal fuse 130º C. Notes: epoxy encapsulated. For mounting on a DIN rail, required bracket: AWO467. Supply voltage: 230V AC. Current consumption: 0.25Amp. Output voltage: 16, 18, 20V. Dimensions: 100 x 137 x 70 mm. Operating temperature: -10 ... +40° C. Protection class: 30IP.

Power: 80VA. Power supply: 230V/50Hz/0.4Amp. Power supply output: 16V/5Amp or 18V/4.5Amp or 20V/4Amp. Enclosure: PC/ABS, V-O, IP30. Thermal fuse 130º C. Notes: epoxy encapsulated. For mounting on a DIN rail, required bracket: AWO467. Supply voltage: 230V AC. Current consumption: 0.40Amp. Output voltage: 16, 18, 20V. Dimensions: 100 x 137 x 70 mm. Operating temperature: -10 ... +40° C. Protection class: 30IP.

Power: 80VA. Power supply: 230V/50Hz/0.4Amp. Power supply output: 17V/4.7Amp or 24V/3.3Amp or 30V/2.7Amp. Enclosure: PC/ABS UL 94 V-0, IP30. Thermal fuse 130º C. Notes: epoxy encapsulated. For mounting on a DIN rail, required bracket: AWO467. Supply voltage: V DC230V AC. Current consumption: 0,40A. Output voltage: 17, 24, 30V. Dimensions: 100 x 137 x 70 mm. Operating temperature: -10 ... +40° C.

Mount bracket for mounting TRP/TRZ transformers on a DIN rail (35mm).

Power: 40VA. Power supply: 230V/50Hz/0.2A. Power supply output: 16V/2.2Amp or 18V/2Amp. Enclosure: PC/ABS, V-O, IP43. Thermal fuse 130º C. Notes: epoxy encapsulated. For mounting on a DIN rail, required bracket: AWO466. Supply voltage: 230V AC. Current consumption: 0.20Amp. Output voltage: 16, 18V. Dimensions: 75 x 124 x 65 mm. Operating temperature: -10 ... +40° C. Protection class: 43IP.